Buy Zhejiang HKE HRS4H-S-DC12V only $ at EasyEDA components online store LCSC. Pushbutton Switches & Relays|Relays datasheet, inventory and. S. Enclosure. Enclosure.: S = Washable. Coil Voltage.: DC5V = 5, DC12V = 12 Disclaimer This data sheet and its contents (the “Information”) belong to the. HRS2(H) Relay – kinds of single relays, power relays, automotive relays, telecom relays, pc-board relays, plug-in relays, P 18/11/04 HRS2H-S DC12V.

Author: Zulujinn Daigis
Country: Solomon Islands
Language: English (Spanish)
Genre: Travel
Published (Last): 5 April 2006
Pages: 484
PDF File Size: 5.56 Mb
ePub File Size: 18.47 Mb
ISBN: 258-5-74503-912-3
Downloads: 97101
Price: Free* [*Free Regsitration Required]
Uploader: Kagagar

For example – the pole of the G2E is connected to two pins.

Some relays have more than one pin connected to a contact. They are generally removed by fitting an external suppressor diode – across the relay coil. By using proper combination of contactors, the electrical circuit can be switched on hrs4h-s-dc12v datasheet off.

The majority of relays are of this type. Relay coils give off high reverse-voltage spikes that will destroy sensitive electronic components. They are often used to interface an electronic circuit working at a low voltage to an electrical circuit which works at very high voltage. Interface SD Card with Arduino. It will establish a new connection with one of the stand alone pins. Low voltage DC relay coils obeys Ohm’s Law. The output section consists of contactors which connect or disconnect mechanically.

Some relays have built-in latches that keep the relay energized after power to the coil is cut. Relay is an electromagnetic device which hrs4h-s-dc12v datasheet used to isolate hrs4h-s-dc12v datasheet circuits electrically and connect them magnetically. So – hrs4h-s-dc12v datasheet check for polarity markings – just in hrs4h-s-dc12v datasheet.


Zhejiang HKE HRS4H-S-DC12V – PDF Datasheet – Relays In Stock |

So – to avoid a short-circuit – the power connections to the coil – MUST be made the right way round. Some relays have two coils. These spikes are generated by the coil – when the relay de-energizes – and the coil’s magnetic field collapses. Start with a normally-closed pair. Thus a small sensor circuit can drive, say, a fan or an electric hrs4h-s-dc12v datasheet. In a basic relay there are three contactors: One will be the pole – and the other will be the normally-closed contact.

This hrs4h-s-dc12v datasheet is called the operating voltage. Take a careful note of each. With your meter – you should be able to divide hrs4h-s-dc12v datasheet into two groups. When the operating voltage is applied the relay coil gets energized and the COM changes contact to NO. They are very useful devices and allow hrs4h-s-dc12v datasheet circuit to switch another one while they are hrs4h-s-dc12v datasheet separate.

Your relay may have several sets of these change-over contacts. Commonly used relays are available in different configuration of operating voltages like 6V, 9V, 12V, 24V etc. The input section has a coil which generates magnetic field when a small voltage from an electronic circuit is applied to it.

Start by finding the two pins connected to the relay coil. See diode D1 on this Repeat Timer Schematic. The coil pins will be the only pair that exhibit a hrs4h-s-dc12v datasheet. If you have no idea hrs4h-sd-c12v voltage your coil is – start with say 3 volts – and increase hrs4h-s-dc12v datasheet until the relay energizes. Some relays have the transistor switch built-in – and hrs4h-s-dc12v datasheet an additional small base current to energize.


However – Very Rarely – you’ll find a relay that’s fitted with an internal suppressor diode.

Some relays have the suppressor diode built-in. How to identify a relay’s pin connections.

You can do this hrs4h-s-dc12v datasheet your multimeter. When you switch datasheeg the power, the pole should part from the normally-open contact – and return to the normally-closed contact.

HRS4H Datasheet PDF

One of those pins is a pole. Identify a pair of pins hrs4h-s-dc12v datasheet separate when power is applied to datahseet coil. And some pins will stand alone – with no connection to any other pin. With careful observation – and a little logical thought – you can work hrs4h-s-dc12v datasheet exactly what’s happening inside the case.

Interface GPS hrs4h-s-dc12v datasheet Arduino. Always check for any markings that indicate coil polarity.

Thanks for helping us to improve our site

SPI Module of Arduino. If there is an hrs4h-s-dc12v datasheet suppressor diode – it’s important that the coil is connected the right way round.

When power is applied to the coil – the pole hrs4h-s-dc12v datasheet part from the normally-closed contact – and establish a new connection with the normally-open contact.